Guru Nanak Dev Engg College Ludhiana (Training & Placement Cell) Format for Synopsis
|
|  Yüklə 51 Kb.
|
| Guru Nanak Dev Engg College Ludhiana
(Training & Placement Cell) Format for Synopsis
Title page: 1. Name of Student and PTU registration No cum Roll No 2. Present official Address with E-mail, telephone No 3. Branch 4. Session 6. Proposed Project Topic: 7. Name of Department/College Introduction to Company(should not exceed 3 pages including Figs.) Brief Introduction to Project (should not exceed 3 pages) Design of solution (should not exceed 3 pages) Methodology/ Planning of work (should not exceed 4 pages) Facilities required for proposed work
5. References and Bibliography should be included in report. 7. The diagrams should be printed on a light/white background, Tabular matter should be clearly arranged. Decimal point may be indicated by full stop(.)The caption for Figure must be given at the BOTTOM of the Fig. and Caption for the Table must be given at the TOP of the Table. 8. The graphs should be combined for the same parameters for proper comparison. Single graph should be avoided as far as possible. 9. Conclusions must not exceed more than two pages. 10. The report must consist of following chapters Chapter 1- Introduction to organization Chapter 2- Project Review Chapter 3- Project work (It can span in two to three sub chapters) Chapter 4- Results and Discussion Chapter 5-Conclusions and future scope References Appendix (if any) Annexures-I,II,III 11. There should be 3 copies of Final Report.
Sample sheet (outer cover) STATISTICAL PROCESS CONTROL OF MECHANICAL LOCKING SYSTEM FOR AUTOMOTIVES (24pt.)
REPORT (14pt.)
SUBMITTED IN PARTIAL FULFILLMENT OF THE REQUIREMENT FOR Six Month Industrial Training at
(from _____ to ________)
SUBMITTED BYPriyanka Walia (14pt) Branch Roll No.
Univ. Roll No.
GNDEC Logo
Information Technology Department GURU NANAK DEV ENGINEERING COLLEGE LUDHIANA, INDIA (14pt.)
Sample sheet (inner title page)
STATISTICAL PROCESS CONTROL OF MECHANICAL LOCKING SYSTEM FOR AUTOMOTIVES
SUBMITTED IN PARTIAL FULFILLMENT OF THE REQUIREMENT FOR Six Month Industrial Training at
(from _____ to ________)
SUBMITTED BYPriyanka Walia (14pt) Branch Roll No.
Univ. Roll No.
GNDEC Logo
Information Technology Department GURU NANAK DEV ENGINEERING COLLEGE LUDHIANA, INDIA (14pt.)
GURU NANAK DEV ENGINEERING COLLEGE, LUDHIANA
TO WHOM IT MAY CONCERN
I hereby certify that “NAME OF THE STUDENT” Roll No ___________ of Guru Nanak Dev Engineering College Ludhaina, has undergone six/two month industrial training from ____________ to ________________at our organization to fulfill the requirements for the award of degree of B.Tech. (Branch).He/She works on _____________ project during the training under the supervision of __________________. . During his tenure with us we found him sincere and hard working. Wishing him a great success in the future. Signature of the Student
Signature of the SUPERVISOR (S)
(Seal of Organization)
ACKNOWLEDGEMENT
The authors are highly grateful to the Dr. H. K. Grewal, Principal, Guru Nanak Dev Engineering College (GNDEC), Ludhiana, for providing this opportunity to carry out the six month industrial training at _________________.
The constant guidance and encouragement received from Er. K. S. Mann Dean T&P, GNDEC Ludhiana has been of great help in carrying out the project work and is acknowledged with reverential thanks. The authors would like to express a deep sense of gratitude and thanks profusely to _ ___________Director/CEO of Company , . Without the wise counsel and able guidance, it would have been impossible to complete the report in this manner.
The help rendered by Mr Gurinder Singh Brar, Supervisor (________________) for experimentation is greatly acknowledged. The author express gratitude to other faculty members of Information Technology department of GNDEC for their intellectual support throughout the course of this work.
Finally, the authors are indebted to all whosoever have contributed in this report work and friendly stay at _______________.
Priyanka Walia
|